RICOH Manuals

Rx5C348A/B are CMOS real-time clock ICs connected to the CPU by four signal lines, CE, SCLK, SI, SO, and configured to perform serial transmission of time and calendar data to the CPU.

File format: PDF Size:1446 KB

The RV5C339A is a CMOS real-time clock IC connected to the CPU by three signal lines CE (Chip Enable), SCLK (Serial Clock), and SIO (Serial Input/Output), and configured to perform serial transmission of time and calendar data to the CPU. This model incorporates different functional circuits, including the periodic interrupt circuit, 2 alarm circuits, oscillation circuit, oscillation halt sensing circuit, supply voltage monitoring circuit, 32-kHz clock output function, and oscillation adjustment circuit. The product features ultra-compact size and low power consumption.

File format: PDF Size:370 KB

The R×5C338A is a 3-wire serial interface real-time clock IC with voltage monitoring function. It is connected to the CPU through three signal lines and performs serial transmission of time and calendar data. It incorporates a periodic interrupt circuit, two alarm circuits, an oscillation circuit, an oscillation halt sensing circuit, a supply voltage monitoring circuit, a 32-kHz clock output function, and an oscillation adjustment circuit.

File format: PDF Size:372 KB

R2062 SERIES 3 wire interface Real-Time Clock ICs with Battery Backup switch-over Function

File format: PDF Size:739 KB

R2061 SERIES 3 wire interface Real-Time Clock ICs with Battery Backup switch-over Function

File format: PDF Size:779 KB

The R2033K/T is a 3 wire interface real-time clock IC, which is a CMOS real-time clock IC using a capacitor oscillator of 32.768kHz as the clock frequency, generating 1 second clock pulses through the internal clock circuit, and generating clock interrupts and calendar interrupts through the internal circuit.

File format: PDF Size:589 KB

R2221T/L R2223T/L 2-wire Serial Interface Real Time Clock IC is a CMOS real-time clock IC connected to the CPU by two signal lines, SCL, SDA, and configured to perform serial transmission of time and calendar data to the CPU.

File format: PDF Size:780 KB

The R2051 is a CMOS real-time clock IC connected to the CPU by two signal lines, SCL and SDA, and configured to perform serial transmission of time and calendar data to the CPU.

File format: PDF Size:724 KB

The R2025S/D is a high-precision I2C bus real-time clock module, built-in CMOS real-time clock IC and crystal oscillator, connected to the CPU by two signal lines, SCL and SDA, and configured to perform serial transmission of time and calendar data to the CPU. The oscillation frequency is adjusted to high precision (0±5 ppm: 15 sec. per month at 25°C) The periodic interrupt circuit is configured to generate interrupt signals with six selectable interrupts ranging from 0.5 seconds to 1 month. The 2 alarm interrupt circuits generate interrupt signals at preset times. As the oscillation circuit is driven under constant voltage, fluctuation of the oscillator frequency due to supply voltage is small, and the time keeping current is small (TYP. 0.48μA at 3V). The oscillation halt sensing circuit can be used to judge the validity of internal data in such events as power-on; The supply voltage monitoring circuit is configured to record a drop in supply voltage below two selectable supply voltage monitoring threshold settings. The 32-kHz clock output function (CMOS output) is intended to output sub-clock pulses for the external microcomputer. The oscillation adjustment circuit is intended to adjust time by correcting deviations in the oscillation frequency of the crystal oscillator.

File format: PDF Size:867 KB

R2023K/T is a CMOS real-time clock IC connected to the CPU by two signal lines, SCL, SDA, and configured to perform serial transmission of time and calendar data to the CPU. The periodic interrupt circuit is configured to generate interrupt signals with six selectable interrupts ranging from 0.5 seconds to 1 month. The 2 alarm interrupt circuits generate interrupt signals at preset times. As the oscillation circuit is driven under constant voltage, fluctuation of the oscillator frequency due to supply voltage is small, and the time keeping current is small (TYP. 0.45µA at 3V).

File format: PDF Size:562 KB

The RS5C372A is a CMOS-type I2C bus interface real-time clock IC that uses 2 wires to connect to the CPU and is capable of serially transmitting clock and calendar data to the CPU. The RS5C372A can generate various periodic interrupt clock pulses lasting for long periods (one month), and alarm interrupt can be made by days of the week, hours, and minutes by two incorporated systems. Since an oscillation circuit is driven at a constant voltage, it undergoes fluctuations of few voltage and consequently offers low current consumption (Typ. 0.5μA at 3V). It also provides an oscillator halt sensing function applicable for data validation at power-on and other occasions and 32-kHz clock output for an external micro computer. (Nch. open drain output) The product also incorporates a time trimming circuit that adjusts the clock with higher precision by adjusting any errors in crystal oscillator frequencies based on signals from the CPU. The crystal oscillator may be selected from 32.768kHz or 32.000kHz types. Integrated into an ultra compact and ultra thin 8 pin SSOP package, the RS5C372A is the optimum choice for equipment requiring small sized and low power consuming products.

File format: PDF Size:528 KB

This product is a CMOS real-time clock IC with I2C bus serial interface and voltage monitoring function

File format: PDF Size:513 KB

The RV5C387A is a CMOS real-time clock IC connected to the CPU by two signals, SCL and SDA, and configured to perform serial transmission of time and calendar data to the CPU. The periodic interrupt circuit is configured to generate interrupt signals with six selectable interrupts ranging from 0.5 seconds to 1 month. The 2 alarm circuits generate interrupt signals at preset times. The oscillation circuit is driven under constant voltage so that fluctuations in oscillation frequency due to voltage are small and supply current is also small (TYP. 0.35µA for the RV5C387A at 3 volts). The oscillation halt sensing circuit can be used to judge the validity of internal data in such events as power-on. The supply voltage monitoring circuit is configured to record a drop in supply voltage below two selectable supply voltage monitoring threshold settings. The 32-kHz clock output function (Nch. open drain) is intended to output sub-clock pulses for the external microcomputer. The oscillation adjustment circuit is intended to adjust time counts with high precision by correcting deviations in the oscillation frequency of the crystal oscillator. The 32-kHz clock circuit can be disabled by certain register settings. This model comes in an ultra- compact 10-pin SSOP-G (with a height of 1.20mm and a pin pitch of 0.5mm).

File format: PDF Size:512 KB

The RB5C634A is a one-chip coder equipped with image compression function of generating JPEG2000-compliant codes and decompression function of decoding images from the JPEG2000-compliant codes. It provides powerful encoding and decoding functionality by simply setting up parameters in the internal registers. This coder can process an image of up to 1024 x 1024 pixels within one tile, which presents the ideal solution for reducing the degradation in image quality to a large extent.

File format: PDF Size:105 KB

The R1283x 2ch DC/DC converter is designed for CCD & OLED Display power source. It contains a step up DC/DC converter and an inverting DC/DC converter to generate two required voltages by CCD & OLED Display. Step up DC/DC converter generates boosted output voltage up to 20V. Inverting DC/DC converter generates negative voltage up to VIN voltage minus 20V independently. Start up sequence is internally made. Each of the R1283x series consists of an oscillator, a PWM control circuit, a voltage reference, error amplifiers, over current protection circuits, short protection circuits, an under voltage lockout circuit (UVLO), an Nch driver for boost operation, a Pch driver for inverting. A high efficiency boost and inverting DC/DC converter can be composed with external inductors, diodes, capacitors, and resistors.

File format: PDF Size:527 KB

The R1283K Series are dual output CMOS-based PWM step-up/inverting DC/DC converters. R1283K includes a soft start circuit, an under-voltage lockout circuit (UVLO), and a latch protection circuit. By simply using inductors, resistors, capacitors, and diodes as external components, a high-efficiency step-up/inverting DC/DC converter can be easily configured. While R1280D need using an external transistor, R1283K has internal 400mΩ ON resistance transistors for both step-up and inverting. Start-up sequence of two DC/DC converters can be selected. Since the shutdown sequence can also be set by the auto-discharge function of the inverting DC/DC converter, the products are ideally suitable for applications that require setting of power supply start-up/shutdown sequence for CCD, LCD, and OLED.

File format: PDF Size:243 KB

The R1286 series 2ch DC/DC power converter is designed for AMOLED display power source. It contains a step up DC/DC converter and an inverting DC/DC converter. Step up DC/DC converter generates boosted output voltage to 4.6V ~ 5.8V(Selectable). Inverting DC/DC converter generates negative voltage down to -2.0V ~ -6.0V(Selectable) that is dynamically adjustable with single wire interface signal. R1286 consist of a voltage reference, error amplifiers, an oscillator, PWM control circuits, over current protection circuits, short protection circuits, an under voltage lockout circuit (UVLO), thermal shutdown circuit, a NMOS driver and a synchronous PMOS switch for boost converter, a PMOS driver and a synchronous NMOS switch for inverting converter, and so on. High efficiency boost and inverting DC/DC converters can be composed with two external inductors and three capacitors.

File format: PDF Size:858 KB

The R1286K Series are CMOS-based PWM step-up/inverting DC/DC converters featuring 250mA×2 output current with synchronous rectifier. R1286K includes a soft start circuit, an under-voltage lockout circuit (UVLO), a latch protection circuit, a thermal shutdown circuit, and a shutdown circuit. By simply using two inductors and three capacitors as external components, a high-efficiency step-up/inverting DC/DC converter can be easily configured. R1286K is available in two types: R1286K001B is the type to which the output voltage (VOUTP and VOUTN) can be adjusted by external resistors. R1286KxxxA/C~M are the type to which the step-up output voltage (VOUTP) is internally fixed and the inverting output voltage (VOUTN) can be adjusted dynamically by the single wire interface. The R1286K has a sequenced start up. After the CE pin is enabled, the step-up output is starting up followed by the inverting output after a delay time. As for shutdown, both outputs will be turned off by the auto-discharge function. R1286K is used for applications such as LCD and AMOLED displays.

File format: PDF Size:343 KB

The R1215D Series are CMOS-based PWM step-up DC/DC converter controllers with low supply current. Each of the R1215D Series consists of an oscillator, a PWM comparator circuit, a reference voltage unit, an error amplifier, a reference current unit, a protection circuit, and an under voltage lockout (UVLO) circuit. A low ripple, high efficiency step-up DC/DC converter can be composed of this IC with some external components, or an inductor, a diode, a power MOSFET, resisters, and capacitors. Maximum duty cycle and the soft start time are easily adjustable with external resistors and capacitors. As for the protection circuit, after the soft-starting time, if the maximum duty cycle is continued for a certain period, the R1215D Series latch the external driver with its off state, or the latch-type protection circuit works. The delay time for latch the state can be set with an external capacitor. To release the protection circuit, restart with power-on (Voltage supplier is equal or less than UVLO detector threshold level).

File format: PDF Size:341 KB

The R1215D Series are low supply current CMOS PWM step-up DC/DC controllers. R1215D does not include an internal output transistor. By simply using a power MOS, an inductor, a diode, resistors, and capacitors as external components, a high-efficiency step-up DC/DC converter can be easily configured.

File format: PDF Size:174 KB