ATMEL Manuals (Industrial)

ATMEL AT22V10B DATA SHEET

The AT22V10B is an ultra-high performance CMOS Programmable Logic Device (PLD). Speeds down to 7.5 ns and operation up to 166 MHz are offered. All pins offer a low ± 10 µA leakage. The AT22V10B logic functionality is fully compatible with the standard 22V10. The 12 dedi- cated inputs and ten configurable I/O pins allow implementation of logic requiring up to 22 input signals. The AT22V10B also provides individual output enable product terms for each of the ten I/Os. (continued)

File format: PDF Size:218 KB

ATMEL AT93C46C 3-Wire Serial EEPROM

The AT93C46C is a 1024-bit serial electrically-erasable programmable read only memory (EEPROM) optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential.

File format: PDF Size:159 KB

ATMEL AT49F002A/AT49F002AN/AT49F002AT/AT49F002ANT 2-megabit (256K x 8) 5-volt Only Flash Memory

This product is a 5-volt only in-system reprogrammable Flash memory with features such as fast read access time, internal program control and timer, sector architecture, fast erase cycle time, byte-by-byte programming, hardware data protection, low power dissipation, typical 10,000 write cycles, green (Pb/Halide-free) packaging option.

File format: PDF Size:214 KB

ATMEL AT49F001 AT49F001N AT49F001T AT49F001NT handbook

The AT49F001(N)(T) is a 5-volt-only in-system reprogrammable Flash Memory with features such as single voltage operation, fast read access time, sector architecture, fast erase cycle time, and byte by byte programming.

File format: PDF Size:157 KB

ATMEL PC107A Preliminary Specification alpha Site Data Sheet

The PC107A PCI Bridge/Integrated Memory Controller features a processor bus frequency of up to 100 MHz, a 64-bit or 32-bit data bus, and a 32-bit address bus. It supports asynchronous SRAM, burst SRAM, or pipelined burst SRAM. It is compliant with PCI Specification, Revision 2.1 and operates at up to 66 MHz/5.0V. It also complies with the IEEE 1149.1 standard for JTAG boundary-scan interface. The controller offers power-saving modes such as Nap, Doze, and Sleep. It includes a two-channel integrated DMA controller, a message unit with intelligent I/O, an Inter-Integrated Circuit controller, and an embedded programmable interrupt controller with five hardware interrupts or 16 serial interrupts.

File format: PDF Size:373 KB

ATMEL AT83SND1C AT89C51SND1C AT80C51SND1C handbook

This is the datasheet of AT89C51SND1C. AT89C51SND1C is a single chip microcomputer with integrated MP3 decoder.

File format: PDF Size:1637 KB

ATMEL AT40K05 AT40K05LV AT40K10 AT40K10LV AT40K20 AT40K20LV AT40K40 AT40K40LV handbook

This document describes a high-performance system with speeds up to 100 MHz, array multipliers over 50 MHz, and flexible 10 ns SRAM. It also provides FreeRAM™, a flexible single/dual port synchronous/asynchronous 10 ns SRAM with 2,048 to 18,432 bits of distributed SRAM independent of logic cells. Additionally, the system features 128 to 384 PCI compliant I/Os, 8 global clocks, and pin-compatible package options. The system supports Cache Logic® dynamic full/partial re-configurability in-system, enabling unlimited re-programmability and fast design changes.

File format: PDF Size:708 KB

ATMEL TS80C51RA2/RD2 TS83C51RB2/RC2/RD2 TS87C51RB2/RC2/RD2 Data Sheet

This datasheet introduces TS80C51RA2/RD2, TS83C51RB2/RC2/RD2, TS87C51RB2/RC2/RD2 three types of Atmel high performance CMOS ROM, OTP, EPROM and ROMless versions of the 80C51 CMOS single chip 8-bit microcontrollers.

File format: PDF Size:442 KB

ATMEL ATmega163/ATmega163L handbook

This document introduces the features and characteristics of the Atmel ATmega328P-AU 8-bit microcontroller

File format: PDF Size:1978 KB

ATMEL AT83C5111/AT87C5111 handbook

AT8xC5111 is a high-performance ROM/OTP version of the 80C51 8-bit microcontroller in low pin count package.

File format: PDF Size:609 KB

ATMEL AT75C221 Summary handbook

The AT75C221 is a high-performance intelligent network appliance processor for professional network appliance applications such as the Ethernet IP phone. The processor is based on an ARM7TDMI microcontroller core running at 40 MHz with an OakDSPCore coprocessor running at 60 MHz and a dual Ethernet 10/100 Mbit/s MAC interface.

File format: PDF Size:209 KB

ATMEL U211B handbook

The U211B is an integrated circuit designed as a phase-control circuit in bipolar technology with an internal frequency-voltage converter. It also has an internal control amplifier, making it suitable for speed-regulated motor applications. It features integrated load limitation, tacho monitoring, soft-start functions, etc. to enable sophisticated motor control systems.

File format: PDF Size:173 KB

ATMEL B10011S CAN Transceiver handbook

B10011S is a CAN bus system transceiver with high output voltage. It is designed for point-to-point interface between truck and trailer according ISO WD 11992-1

File format: PDF Size:70 KB

ATMEL ATF16V8B handbook

The document describes the features and characteristics of the ATF16V8B high-performance CMOS programmable logic device, including industry-standard architecture, high-speed electrically erasable programmable logic devices, several power-saving options, CMOS and TTL compatible inputs and outputs, advanced Flash technology, high reliability CMOS process, etc.

File format: PDF Size:641 KB

ATMEL ATF1502ASV handbook

This high-density, high-performance electrically-erasable complex programmable logic device has a 3.0 to 3.6V operating range, 32 macrocells, 5 product terms per macrocell, expandable up to 40 per macrocell, 44 pins, 15 ns maximum pin-to-pin delay, registered operation up to 77 MHz, and enhanced routing resources.

File format: PDF Size:205 KB

ATMEL AT49F010/AT49HF010 handbook

The AT49F010/HF010 1-Megabit (128K x 8) 5-volt Only CMOS Flash Memory is an in-system programmable and erasable Flash Memory manufactured by Atmel. Their 1-megabit of memory is organized as 131,072 words by 8 bits. Manufactured with Atmel's advanced nonvolatile CMOS technology, the devices offer access times to 45 ns (HF version) with a power dissipation of just 165 mW over the commercial temperature range. When the device is deselected, the CMOS standby current is less than 100 µA. To allow for simple in-system reprogrammability, the AT49F010/HF010 does not require high input voltages for programming. Five-volt-only commands determine the read and programming operation of the device. Reading data out of the device is similar to reading from an EPROM. Reprogramming the AT49F010/HF010 is performed by erasing the entire 1 megabit of memory and then programming on a byte by byte basis.

File format: PDF Size:250 KB

ATMEL AT49F004/AT49F004T/AT49F4096A/AT49F4096AT handbook

The AT49F004(T) and AT49F4096A(T) are 5-volt, 4-megabit Flash Memories orga- nized as 524,288 words of 8 bits each or 256K words of 16 bits each. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the devices offer access times to 55 ns with power dissipation of just 275 mW. When deselected, the CMOS standby current is less than 300 µA. The device contains a user-enabled “boot block” protection feature. Two versions of the feature are available: the AT49F004/4096A locates the boot block at lowest order addresses (“bottom boot”); the AT49F004T/4096AT locates it at highest order addresses (“top boot”). To allow for simple in-system reprogrammability, the AT49F004(T)/4096A(T) does not require high input voltages for programming. Reading data out of the device is similar to reading from an EPROM; it has standard CE, OE, and WE inputs to avoid bus con- tention. Reprogramming the AT49F004(T)/4096A(T) only requires one pin, CE. For most operations, the other pins are in high-impedance state.

File format: PDF Size:248 KB

ATMEL AT34C02B handbook

The AT34C02B is a serial electrically-erasable and programmable read only memory (EEPROM) with 256 x 8 bits organization. It features permanent and reversible software write protection for the first-half of the array, hardware write protection for the entire array, low-voltage and standard-voltage operation, two-wire serial interface, bidirectional data transfer protocol, and compatibility with different clock speeds. It also has high-reliability with endurance of 1 million write cycles and data retention of 100 years. The package options include JEDEC SOIC, Ultra Thin Mini-MAP (MLP 2x3), TSSOP, and dBGA2.

File format: PDF Size:447 KB

ATMEL T0782 Data Sheet

The T0782 is a high-linearity active mixer which is manufactured using Atmel’s advanced Silicon-Germanium technology. This mixer features a frequency range of 2200 MHz to 2700 MHz. It operates from a single 5-V supply and provides 10 dB of conversion gain while requiring only 0 dBm input to the integrated LO driver. An IF amplifier is also included. The T0782 incorporates internal matching on each RF, IF and LO port to enhance ease of use and to reduce the external components required. The RF and LO inputs can be driven differentially or single-ended.

File format: PDF Size:295 KB

ATMEL U209B handbook

The U209B is a phase-control integrated circuit designed for motor speed control with tacho feedback. It features an internal frequency-to-voltage converter, externally controlled integrated amplifier, automatic soft start, voltage and current synchronization, retriggering, and more.

File format: PDF Size:89 KB

Brands



Products